Tooling and Mould Ownership in Ontario Manufacturing Agreements: Who Owns It, Who Pays and What Happens at the End
A customer pays you to build a $90,000 injection mould. Three years later it moves the program to another supplier and asks for the mould back. You have amortized part of the cost into the piece price, you have repaired the mould twice at your own expense, and the customer still owes you for the last two shipments.

Who owns that mould, who pays for what and whether you can hold it until you are paid all depend on terms most manufacturing agreements leave out. For an Ontario manufacturer, tooling terms belong in writing before the first part is made.
In this article
1. Settle Tooling and Mould Ownership Before Work Starts
Tooling disputes usually start with a quote that says “tooling: $90,000” and nothing more. That line does not say whether the customer is buying the tool, paying for your cost of building a tool you keep, or paying a charge for access to your capacity. Each answer leads to a different result when the relationship ends.
State tooling and mould ownership expressly. If the customer will own the tool, say when title passes, often on full payment of the tooling invoice, and how the tool will be identified as customer property. If you will own it, say so, and state that tooling charges do not transfer ownership.
A tooling line on a quote is a price. It is not an ownership agreement.
2. Separate Who Pays for Tooling From Who Owns It
Many customers prefer to pay for tooling through the piece price rather than up front. That spreads the cost, but it creates a problem if volumes fall short or the program ends early. If the tool was to be paid off over 500,000 parts and the customer buys 200,000, the unrecovered balance needs a home.
The agreement should say how tooling is paid for, what happens to any unpaid balance on early termination or a volume shortfall, and whether ownership transfers only once the tool is fully paid. Our article on investing in equipment for a major customer covers the same recovery risk for larger capital commitments.
3. Assign Maintenance, Repair, Insurance and Replacement
Tools wear out. Moulds and dies need routine maintenance, periodic repair and eventually replacement. If the agreement is silent, the manufacturer usually absorbs these costs while the customer assumes it owns a tool in good working order.
Set out who pays for routine maintenance, who pays for repairs beyond normal wear, who decides when a tool must be replaced and who pays for the replacement. Confirm who insures customer owned tooling while it sits in your plant, and agree on what happens if it is damaged or destroyed.
Building or holding tooling for a customer? Book a consultation and we will tell you which ownership, payment and exit terms to accept, negotiate or escalate before you commit.
4. Control Use, Location and Confidential Designs
Customers often require that their tooling be used only for their parts, kept at a named location and not moved without consent. Those are reasonable requests, but they affect how you schedule production and plan your floor. Agree on them deliberately rather than accepting them in the customer’s general terms.
Address the design as well as the physical tool. If your engineers designed the tool, the agreement should say who owns that design, whether the customer can give your drawings to another supplier and whether you can use the same design approach for other customers. Related questions about who owns the customer relationship and the IP come up in distribution relationships too.
5. Plan the Exit Before the First Part Ships
The end of a program is when tooling terms are tested. The agreement should say how much notice the customer must give to remove its tooling, who pays to package and ship it, what condition it will be returned in and whether you may keep it until every outstanding invoice, including any unpaid tooling balance, has been paid.
Exit terms should also address last time buys, storage charges if the customer leaves tooling with you after the program ends and what happens to tooling the customer never collects. Review these terms alongside your termination clauses, since the two usually operate together. For packaging suppliers, our article on tooling, forecast changes and unused inventory covers related issues.
Frequently Asked Questions
Who owns tooling if the agreement does not say?
It depends on the facts, including what the quote and invoices say, who paid for the tool and how the parties dealt with it. That uncertainty is the reason to state tooling ownership expressly in the agreement.
Does paying a tooling charge mean the customer owns the tool?
Not necessarily. A tooling charge may be a purchase price, a contribution to your costs or a fee for capacity. The agreement should say which one it is and when, if ever, title passes.
Can we hold a customer’s tooling until we are paid?
Only on the terms the agreement and the law allow. A clear contractual right to retain tooling until all amounts are paid gives you far more certainty than relying on general rules.
Who should pay for tooling maintenance and replacement?
Commonly, the manufacturer covers routine maintenance and the owner pays for major repairs and replacement. The right split depends on your pricing, and it should be written down either way.
What should happen to tooling when a program ends?
The agreement should cover notice for removal, shipping costs, return condition, payment of outstanding amounts, storage charges and what happens to tooling that is never collected.
Learn More
To see how we support contract manufacturers and fabricators, visit our Legal Services for Contract Manufacturers & Fabricators page, or explore our Legal Services for Manufacturers & Distributors.
Is your tooling arrangement in writing?
Ownership, payment, maintenance and return terms decide who carries the cost of tooling when a program changes or ends. Delta Law helps Ontario manufacturers set those terms before production starts.
This article provides general information only and is not legal advice. Reading it does not create a lawyer-client relationship.



